Hostname: page-component-7c8c6479df-hgkh8 Total loading time: 0 Render date: 2024-03-28T03:48:34.938Z Has data issue: false hasContentIssue false

Nanoindentation analysis as a two-dimensional tool for mapping the mechanical properties of complex surfaces

Published online by Cambridge University Press:  31 January 2011

Nicholas X. Randall*
Affiliation:
CSM Instruments, Needham, Massachusetts 02494
Matthieu Vandamme
Affiliation:
CSM Instruments, Needham, Massachusetts 02494
Franz-Josef Ulm
Affiliation:
Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139
*
a) Address all correspondence to this author. e-mail: nra@csm-instruments.com
Get access

Abstract

Instrumented indentation (referred to as nanoindentation at low loads and low depths) has now become established for the single point characterization of hardness and elastic modulus of both bulk and coated materials. This makes it a good technique for measuring mechanical properties of homogeneous materials. However, many composite materials are composed of material phases that cannot be examined in bulk form ex situ (e.g., carbides in a ferrous matrix, calcium silicate hydrates in cements, etc.). The requirement for in situ analysis and characterization of chemically complex phases obviates conventional mechanical testing of large specimens representative of these material components. This paper will focus on new developments in the way that nanoindentation can be used as a two-dimensional mapping tool for examining the properties of constituent phases independently of each other. This approach relies on large arrays of nanoindentations (known as grid indentation) and statistical analysis of the resulting data.

Type
Articles
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Doerner, M.F. and Nix, W.D.: A method for interpreting the data from depth-sensing indentation instruments. J. Mater. Res. 1, 601 (1986).CrossRefGoogle Scholar
2.Loubet, J.L., Georges, J.M., and Meille, G.: Vickers indentation curves of elastoplastic materials, in Microindentation Techniques in Materials Science and Engineering, edited by Blau, P.J. and Lawn, B.R. (ASTM Intl., West Conshohocken, PA, 1986), p. 72.Google Scholar
3.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
4.Randall, N.X., Christoph, R., Droz, S., and Julia-Schmutz, C.: Localized micro-hardness measurements with a combined scanning force microscope/nanoindentation system. Thin Solid Films 291, 348 (1996).CrossRefGoogle Scholar
5.Constantinides, G., Ulm, F-J., and Van Vliet, K.J.: On the use of nanoindentation for cementitious materials. Mater. Struct. 36, 191 (2003).CrossRefGoogle Scholar
6.Ulm, F-J., Constantinides, G., and Heukamp, F.H.: Is concrete a poromechanics material? A multiscale investigation of poroelas-tic properties. Mater. Struct. 37, 43 (2004).CrossRefGoogle Scholar
7.Constantinides, G. and Ulm, F-J.: The effect of two types of C-S-H on the elasticity of cement-based materials: Results from nanoindentation and micromechanical modeling. Cem. Concr. Res. 34, 67 (2004).CrossRefGoogle Scholar
8.Constantinides, G., Chandran, K.S.R., Ulm, F-J., and Van Vliet, K.J.: Grid indentation analysis of composite microstructure and mechanics: Principles and validation. Mater. Sci. Eng., A 430, 189 (2006).CrossRefGoogle Scholar
9.Constantinides, G. and Ulm, F-J.: The nanogranular nature of C-S-H. J. Mech. Phys. Solids 55, 64 (2007).CrossRefGoogle Scholar
10.Ulm, F-J., Vandamme, M., Bobko, C., Ortega, J.A., Tai, K., and Ortiz, C.: Statistical indentation techniques for hydrated nanocom-posites: Concrete, bone, and shale. J. Am. Ceram. Soc. 90, 2677 (2007).CrossRefGoogle Scholar
11.Vandamme, M. and Ulm, F-J.: The nanogranular origin of concrete creep: A nanoindentation investigation of microstructure and fundamental properties of calcium-silicate-hydrates, CEE Report R08–01 (Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2008).Google Scholar
12.Constantinides, G. and Ulm, F-J.: Invariant mechanical properties of calcium-silicate-hydrates (C-S-H) in cement-based materials: Instrumented nanoindentation and microporomechanical modeling, CEE Report R06–01 (Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, MA, 2006).Google Scholar
13.Durst, K., Goken, M., and Vehoff, H.: Finite element study for nanoindentation measurements on two-phase materials. J. Mater. Res. 19, 85 (2004).CrossRefGoogle Scholar
14.Perriot, A. and Barthel, E.: Elastic contact to a coated half-space: Effective elastic modulus and real penetration. J. Mater. Res. 19, 600 (2004).CrossRefGoogle Scholar
15.Hurley, D.C., Kopycinska-Müller, M., Kos, A.B., and Geiss, R.H.: Nanoscale elastic-property measurements and mapping using atomic force acoustic microscopy. Meas. Sci. Technol. 16, 2167 (2005).CrossRefGoogle Scholar
16.Asif, S.A., Wahl, K.J., Colton, R.J., and Warren, O.L.: Quantitative imaging of nanoscale mechanical properties using hybrid nanoindentation and force modulation. J. Appl. Phys. 90(3), 1 (2001).Google Scholar
17.Dormieux, L., Kondo, D., and Ulm, F-J.: Microporomechanics, 1st ed. (John Wiley & Sons, New York, NY, 2006).CrossRefGoogle Scholar
18.Hershey, A.V.: The elasticity of an isotropic aggregate of anisotropic cubic crystals. J. Appl. Mech. 21, 236 (1954).CrossRefGoogle Scholar
19.Kröner, E.: Calculation of the elastic constants of a polycrystal from the constants of the single crystal. Z. Phys. 151, 504 (1958).CrossRefGoogle Scholar
20. International Organization for Standardization: ISO 14577, Metallic materials-Instrumented indentation test for hardness and materials parameters (International Organization for Standardization, 2007).Google Scholar