Hostname: page-component-7c8c6479df-27gpq Total loading time: 0 Render date: 2024-03-28T08:53:17.054Z Has data issue: false hasContentIssue false

Numerical predictions for laminar source-sink flow in a rotating cylindrical cavity

Published online by Cambridge University Press:  20 April 2006

J. W. Chew
Affiliation:
School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, England Present address: Theoretical Science Group, Rolls-Royce Limited, P.O. Box 31, Derby, England.
J. M. Owen
Affiliation:
School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, England
J. R. Pincombe
Affiliation:
School of Engineering and Applied Sciences, University of Sussex, Falmer, Brighton, England

Abstract

Numerical solutions are presented for steady, axisymmetric, laminar, isothermal, source–sink flow in a rotating cylindrical cavity. These results, which are in good agreement with previously published experimental work, have been used to give a fresh insight into the nature of the flow and to investigate the validity of other theoretical solutions. When the fluid enters the cavity through a central uniform radial source and leaves through an outer sink, it is shown that the flow near the disks can be approximated by two known analytical solutions. If the radial source is replaced by an axial inlet the flow becomes more complex, with a wall jet forming on the downstream disk at sufficiently high flow rates.

Type
Research Article
Copyright
© 1984 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Bennetts, D. A. & Hocking, L. M. 1973 On nonlinear Ekman and Stewartson layers in a rotating fluid. Proc. R. Soc. Lond. A 333, 469.Google Scholar
Bennetts, D. A. & Jackson, W. D. N. 1974 Source—sink flows in a rotating annulus: a combined laboratory and numerical study. J. Fluid Mech. 66, 689.Google Scholar
Chew, J. W. 1984 Development of a computer program for the prediction of flow in a rotating cavity. Intl J. Num. Methods Fluids (to be published).Google Scholar
Cochran, W. G. 1934 The flow due to a rotating disc. Proc. Camb. Phil. Soc. 30, 365.Google Scholar
Faller, A. J. 1963 An experimental study of the instability of the laminar Ekman boundary layer. J. Fluid Mech. 15, 560.Google Scholar
Gosman, A. D. & Ideriah, F. J. K. 1976 Teach-t: A general computer program for two dimensional turbulent recirculating flows. In Calculation of Recirculating Flows. Dept Mech. Engng, Imperial College, University of London.
Hide, R. 1968 On source—sink flows in a rotating fluid. J. Fluid Mech. 32, 737.Google Scholar
Kármán, T. von 1921 Über laminare und turbulente Reibung. Z. angew. Math. Mech. 1, 233.Google Scholar
Owen, J. M. & Bilimoria, E. D. 1977 Heat transfer in rotating cylindrical cavities. J. Mech. Engng Sci. 19, 175.Google Scholar
Owen, J. M. & Onur, H. S. 1983 Convective heat transfer in a rotating cylindrical cavity. Trans. ASME A: J. Engng Power 105, 265.Google Scholar
Owen, J. M. & Pincombe, J. R. 1980 Velocity measurements inside a rotating cylindrical cavity with a radial outflow of fluid. J. Fluid Mech. 99, 111.Google Scholar
Owen, J. M. & Rogers, R. H. 1983 Solution of the integral momentum equations for an Ekman layer in a heated rotating cavity. Part 1: The full equations and the linear approximation. School of Engng and Appl. Sci., Univ. Sussex, Rep. TFMRC/15a.Google Scholar
Pincombe, J. R., Owen, J. M. & Rogers, R. H. 1983 Solution of the integral momentum equations for an Ekman layer in a heated rotating cavity. Part 3. Comparison between theory and experiment. School of Engng and Appl. Sci., Univ. Sussex, Rep. TFMRC/17a.Google Scholar
Rogers, R. H. & Owen, J. M. 1983 Solution of the integral momentum equations for an Ekman layer in a heated rotating cavity. Part 2. The nondimensional form of the equations and the numerical solutions. School of Engng and Appl. Sci., Univ. Sussex, Rep. TFMRC/16a.Google Scholar