Hostname: page-component-7c8c6479df-995ml Total loading time: 0 Render date: 2024-03-29T07:03:52.542Z Has data issue: false hasContentIssue false

Comparison of the Young's moduli of polymers measured from nanoindentation and bending experiments

Published online by Cambridge University Press:  21 July 2014

Ricardo Martinez
Affiliation:
Department of Mechanical Engineering, University of Texas at El Paso, El Paso, Texas 79968
L. Roy Xu*
Affiliation:
Department of Mechanical and Aerospace Engineering, New Mexico State University, Las Cruses, New Mexico 88003
*
Address all correspondence to L. Roy Xu at luoyu.r.xu@gmail.com
Get access

Abstract

Spherical and conical nanoindentation experiments were performed for the same polymer specimens to compare Young's moduli measured from the elastic loading and unloading curves, and bending experiments. Finite-element simulation was employed to ensure pure elastic deformation during spherical nanoindentation. The moduli measured from the elastic loading curves using Hertz's contact law are very close to the bending moduli, because both measurements were conducted under the same elastic deformation. However, the moduli measured from the elastic unloading curves are up to 60% higher than the bending moduli owing to plastic deformation close to the sharp conical indenter tip.

Type
Research Letters
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Wang, P. and Xu, L.R.: Dynamic interfacial debonding initiation induced by an incident crack. Int. J. Solids Struct. 43, 6535 (2006).Google Scholar
2.Wei, X. and Kysar, J.W.: Experimental validation of multiscale modeling of indentation of suspended circular graphene membranes. Int. J. Solids Struct. 49, 3201 (2012).CrossRefGoogle Scholar
3.Xu, L.R., Li, L., Lukehart, C.M., and Kuai, H.: Mechanical property characterization nanofiber-reinforced composite adhesives. J. Nanosci. Nanotechnol. 7, 2546 (2007).Google Scholar
4.Anasori, B. and Barsoum, M.W.: reversible dislocation motion and microcracking in plastically anisotropic solids under cyclic spherical nanoindentation. MRS Communications, available on CJO September 2013. doi: 10.1557/mrc.2013.39.Google Scholar
5.Odegard, G.M., Gate, T.S., and Herring, H.M.: Characterization of viscoelastic properties of polymeric materials through nanoindentation. Exp. Mech. 45, 130 (2005).Google Scholar
6.Lu, Y.C., Jones, D.C., Tandon, G.P., Putthanarat, S., and Schoeppner, G.A.: High temperature nanoindentation of PMR-15 polyimide. Exp. Mech. 50, 491 (2010).CrossRefGoogle Scholar
7.Oyen, M.L. and Cook, R.F.: Load-displacement behavior during sharp indentation of viscous elastic-plastic materials. J. Mater. Res. 18, 139 (2002).CrossRefGoogle Scholar
8.Delafrague, A. and Ulm, F.J.: Explicit approximations of the indentation modulus of elastically orthotropic solids for conical indenters. Int. J. Solids Struct. 41, 7351 (2004).Google Scholar
9.Li, W. and Siegmund, T.: A numerical study of indentation delamination of weakly bonded ductile films on elastic substrates. Acta Mater. 52, 2989 (2004).Google Scholar
10.Gao, Y.F. and Pharr, G.M.: Multidimensional contact moduli of elastically anisotropic solids. Scr. Mater. 57, 13 (2007).Google Scholar
11.Cao, G., Chen, X., Xu, Z.H. and Li, X.D.: Measuring mechanical properties of micro- and nano-fibers embedded in an elastic substrate: theoretical framework and experiment. Composites B 41, 33 (2010).CrossRefGoogle Scholar
12.Cheng, Y.T. and Cheng, C.M.: Relationships between initial unloading slope, contact depth, and mechanical properties for conical indentation in linear viscoelastic solids. J. Mater. Res. 20, 1046 (2005).Google Scholar
13.Donohue, B.R., Ambrus, A., and Kalidindi, S.R.: Critical evaluation of the indentation data analyses methods for the extraction of isotropic uniaxial mechanical properties using finite element models. Acta Mater. 60, 3943 (2012).Google Scholar
14.Feng, C., Tannenbaum, J.M., King, B.S., and Alvin, M.A.: A load-based multiple-partial unloading micro-indentation technique for mechanical property evaluation. Exp. Mech. 50, 737 (2009).CrossRefGoogle Scholar
15.Ghosh, D., Subhash, G., Sudarshan, T.S., Radhakrishnan, R., and Gao, X-L.: Dynamic indentation response of fine-grained boron carbide. J. Am. Ceram. Soc. 90, 1850 (2007).Google Scholar
16.Gerberich, W.W., Kramer, W.Y., Bahr, D., Stronjy, A., Lilleodden, E., and Nelson, J.: Elastic loading and elastoplastic unloading from nanometer level indentations for modulus determinations. J. Mater. Res. 13, 421 (1997).Google Scholar
17.Jee, A-Y. and Lee, M.: Comparative analysis on the nanoindentation of polymers using atomic force microscopy. Polym. Test. 20, 95 (2009).Google Scholar
18.Jha, K.K., Suksawang, N., Lahiri, D., and Agarwal, A.: Evaluating initial unloading stiffness from elastic work-of-indentation measured in a nanoindentation experiment. J. Mater. Res. 28, 789 (2013).Google Scholar
19.McKee, C.T., Last, J.A., Russell, P., and Murphy, C.J.: Indentation versus tensile measurements of Young's modulus for soft biological tissues. Tissue Eng. B 17, 155 (2011).CrossRefGoogle ScholarPubMed
20.Nakamura, T. and Gu, Y.: Identification of elastic–plastic anisotropic parameters using instrumented indentation and inverse analysis. Mech. Mater. 39, 340 (2007).Google Scholar
21.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).Google Scholar
22.Rittel, B.P. and Ravichandran, G.: An analysis of nanoindentation in linearly elastic solids. Int. J. Solids Struct. 45, 6018 (2008).Google Scholar
23.Tranchida, D., Piccarolo, S., Loos, J., and Alexeev, A.: Accurately evaluating Young's modulus of polymers through nanoindentations: a phenomenological correction factor to the Oliver and Pharr procedure. Appl. Phys. Lett. 89, 171905 (2006).CrossRefGoogle Scholar
24.Zhang, C.Y., Zhang, Y.W., Zeng, K.Y., and Shen, L.: Nanoindentation of polymers with sharp indenters. J. Mater. Res. 20, 1597 (2005).Google Scholar
25.Zhou, Z. and Lu, H.: On the measurements of viscoelastic functions of a sphere by nanoindentation. Mech. Time-Depend. Mater. 14, 1 (2010).CrossRefGoogle Scholar
26.Olivas, E.R., Swadener, J.G., and Shen, Y-L.: Nanoindentation measurement of surface residual stresses in particle-reinforced metal matrix composites. Scr. Mater. 54, 263 (2006).Google Scholar
27.Fischer-Cripps, A.C.: Nanoindentation, 2nd ed. (Springer Publisher, New South Wales, Australia, 2011), p. 163.Google Scholar
28.Wu, Y.F., Yu, H.Y., and Chen, W.Q.: Mechanics of indentation for piezoelectric thin films on elastic substrate. Int. J. Solids Struct. 49, 95 (2012).CrossRefGoogle Scholar
29.Krishnan, A. and Xu, L.R.: Experimental studies on the interaction among cracks, notches and interfaces of bonded polymers. Int. J. Solids Struct. 50, 1583 (2014).CrossRefGoogle Scholar
30.Martinez, R. and Xu, L.R.: Approximate measurements of the though-thickness Young's moduli of fibrous composite laminates using nanoindentation. Submitted for publication (2014).Google Scholar
Supplementary material: File

Martinez and Xu Supplementary Material

Figures S1-S3

Download Martinez and Xu Supplementary Material(File)
File 233 KB