Hostname: page-component-7c8c6479df-nwzlb Total loading time: 0 Render date: 2024-03-28T01:02:47.466Z Has data issue: false hasContentIssue false

Mechanical properties of nylon 6-clay hybrid

Published online by Cambridge University Press:  31 January 2011

Yoshitsugu Kojima
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Arimitsu Usuki
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Masaya Kawasumi
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Akane Okada
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Yoshiaki Fukushima
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Toshio Kurauchi
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Osami Kamigaito
Affiliation:
Toyota Central Research & Development Labs., Inc., Nagakute-cho, Aichi-gun, Aichi 480-11 Japan
Get access

Abstract

Various nylon 6-clay hybrids, such as molecular composites of nylon 6 and silicate layers of montmorillonite and saponite, NCH's and NCHP's, respectively, have been synthesized. To estimate the mechanical properties of these hybrids, tensile, flexural, impact, and heat distortion tests were carried out. NCH was found superior in strength and modulus and comparable in impact strength to nylon 6. The heat distortion temperature (HDT) of NCH (montmorillonite: 4.7 wt. %) was 152 °C, which was 87 °C higher than that of nylon 6. In NCHP, saponite had a smaller effect on the increase of these mechanical properties. The modulus and HDT of NCH and NCHP increased with an increase in the amount of clay minerals. It was found that these properties were well described by the contribution of the constrained region calculated from the storage and loss modulus at the glass transition temperature. According to the mixing law on elastic modulus, the following expression was obtained between the modulus E at 120 °C and the fraction of the constrained region C, En = Ecn = C, where the values of n and Ec (modulus of the constrained region) were 0.685 and 1.02 GPa, respectively.

Type
Articles
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Nylon Plastics, edited by Kohan, M.I. (John Wiley & Sons, Inc., New York, 1973).Google Scholar
2Usuki, A.Kojima, Y.Kawasumi, M.Okada, A.Fukushima, Y.Kurauchi, T. and Kamigaito, O.J. Mater. Res. 8, 1179 (1993).Google Scholar
3Bradbury, E. M.Brown, L.Elliot, A. and Parry, D. A. D.Polymer 6, 465 (1965).CrossRefGoogle Scholar
4Okada, A.Kawasumi, M.Tajima, I.Kurauchi, T. and Kamigaito, O.J. Appl. Polym. Sci. 37, 1363 (1989).CrossRefGoogle Scholar
5Mere, K.H.Haberkorn, H. and Simak, P.Makromol. Chem. 158, 285 (1972).Google Scholar
6Nielsen, L. E.Mechanical Properties of Polymers and Composites (Marcel Dekker, New York, 1978).Google Scholar
7Usuki, A.Kojima, Y.Kawasumi, M.Okada, A.Kurauchi, T. and Kamigaito, O., Polymer Preprints, Am. Chem. Soc. Polym. Chem. 31 (2), 659 (1990).Google Scholar
8Krevelen, D. W. Van, Properties of Polymers (Elsevier, Amsterdam, 1987), p. 311.Google Scholar
9Oka, S. and Chikahisa, Y.Kobunshi Bussei (Asakura Syoten, Tokyo, 1974), p. 146.Google Scholar